13+ Humminbird Transducer Wiring Diagram

Adding a MEGA Live Imaging transducer to a boat with 2 bow-mounted Humminbird units and a Minn Kota motor with built-in MEGA Imaging. The transom installation which is the most widely used places the transducer on the outside of the boat hull.

Shop Humminbird Transducers Ice Ducers 360 Imaging Sonar Factory Outlet Store

Web Before installing your new Humminbird fishfinder please ensure the following parts are included in the box.

. Ethernet Adapter Cable Need 2 AS EC QDE 720074-1. Print the electrical wiring diagram off plus use highlighters to be able to trace the signal. Ad Gear Up Your Boat for the Ultimate Fishing Adventure with Humminbird Transducers.

You must connect the drainshield wire and the ground wire on the MEGA 360 power cable to a ground terminalboat chassis ground point to ensure good performance. Installations shown are for HELIX G3NG4N and APEXSOLIX G2G3 networking models and Minn Kota trolling motors with i-Pilot Link. Web MEGA Live Imaging Transducer 710304-1 One 1 AS ECX 30E ethernet extension cable included with i-Pilot Link trol ling motor.

1 Ethernet Adapter Cable Need 2. XTH 9 20. Web 1 bow-mounted Humminbird unit and 1 console-mounted Humminbird unit with heading sensor GPS puck and high-speed transducer with y-cable.

1 Ethernet Adapter Cable AS EC QDE 720074-1 Ethernet Adapter Cable NA 2 GPS Heading Sensor AS GPS HS 408400-1 GPS. This means if you had the MEGA Live Imaging transducer installed prior to adding the MEGA Live TargetLock you will not have to run the additional PC 13 power cable. Connect the transducer cable to the transducer port on the control head.

1 Bow-mounted Humminbird unit and 1 console-mounted unit networked together with heading sensor GPS puck and high-speed transducer with y-cable. Web TRANSDUCER MOUNTING PROCEDURE. The ports are labeled and the connectors are keyed to prevent incorrect installation so do not force the connector into the wrong port.

Mounting system and mounting hardware kit. Web There are three mounting options for the side imaging transducer. Web BRONZE THRU-HULL TRANSDUCER INSTALLATION INSTRUCTIONS For use with the following models.

MEGA Live TargetLock wiring diagram included below. AS EC 5E 5 720073-6 AS EC 10E 10 720073-2 AS EC 15E. Route and secure the transducer cable to the control head avoiding areas where it may be damaged or interfere with normal boating operations.

Get Deals and Low Prices On humminbird transducer y cable At Amazon. See your transducer installation guide for details on routing the transducer cable. The accessories and part numbers listed above are valid as of November 2021.

Ad We Offer a Wide Array Of Products Like Tree Stands Bags More. When you employ your finger or even stick to the circuit with your eyes it. Web Your Humminbird fish finder includes a transom mounted transducer.

Use two tie wrap cables to secure the Transducer Cable to the shaft just above the Lift Assist Collar and just below. Ethernet Adapter Cable Need 2 AS EC QDE 720074-1. The accessories and part numbers listed above are valid as of November 2021.

Transducer with 20 6m of cable and mounting hardware kit. Web Humminbird 405SXpdf 233 Mb Humminbird 425SXpdf 206 Mb Humminbird 55Spdf 18 Mb Humminbird 717_727pdf 135 Mb Humminbird 737pdf 299 Mb Humminbird 747_777pdf 435 Mb Humminbird 757_787pdf 536 Mb. STAINLESS STEEL THRU-HULL TRANSDUCER INSTALLATION INSTRUCTIONS For use with the.

Web MEGA Live TargetLock Wiring Diagram. Web A high-quality transducer is the heart of a Humminbird fish finder. The MEGA Live TargetLock uses the same PC 13 power cable as the MEGA Live Imaging transducer.

Humminbirds high-speed transducer is supplied with your LCR. Web Mount the External Transducer according to directions provided with the transducer. Shop transom mount in-hull thru-hull portable and ice transducers for your fish finder.

6 2m power cable. Transom-mount this transducer comes standard with all Side Imaging units. Plastic thru-hull transducer offered as an optional accessory.

Do not cut or shorten the transducer cable and try not to damage the cable. Please carefully consider the following before installing your transducer. Below is a wiring diagram detailing how the MEGA Live transducer connects to the TargetLock Control Box and how the MEGA Live TargetLock connects to the One Boat Network and power.

Web High Speed Transducer aluminum hull XNT 14 HW T 710285-1. Web HUMMINBIRDCOM FRESHWATER INSTALLATION Minn Kota trolling motor with i-Pilot Link and 1 console-mounted Humminbird unit with heading sensor GPS puck and high-speed transducer with y-cable. Web Connecting the three wires on the power cable of my MEGA 360.

This transducer has been designed to give good high speed readings on most all boat designs including aluminum. The drain wire is the non-tinned wire. The following schematic outlines the necessary accessoriescables needed to add an in-hull transducer and splitter cable to a multi-unit network of three Humminbird units and a Minn Kota trolling motor.

Get the Ultimate Underwater Insight with Humminbirds Precision Transducers. BRONZE THRU-HULL SIDE IMAGING TRANSDUCER INSTALLATION INSTRUCTIONS For use with the following models. Web Two Console Mount and One Bow Mount Humminbird Units a Minn Kota Trolling Motor and an In-Hull Transducer.

Your boat may have a pre-existing wiring channel or conduit that you can use for the transducer cable. Leave enough slack in the Transducer Cable between the Lower Unit and the Control Head to allow the motor to properly stow and deploy. This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat with a two part slow curing epoxy.

Trolling motor mount adapters to allow the transom mount transducer to be mounted to the trolling motor are sold separately.

03 Transducer Installation Youtube